topbanner_forum
  *

avatar image

Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length
  • July 19, 2019, 09:26 AM
  • Proudly celebrating 13 years online.
  • Donate now to become a lifetime supporting member of the site and get a non-expiring license key for all of our programs.
  • donate

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - MartinT [ switch to compact view ]

Pages: [1]
1
Hi JGPAIVA,

Thanks for your efford! Your reply with my edit of my post just crossed eachother, but your solution is just a tad nicer, since the edges are more exact! ( on my file a had to add few units/pixels to align the right grids to the edge of the screen (hence the +2 and +1)

Thanks a million!

regards,
Martin

2
Hello,
Great program, just what I have been looking for a long time!

But.. (there's always one, isn't there... ;))
I do not understand much of the help file regarding custom templates.

I run 3 monitors under a Matrox TripleHead 2Go, which WindowsXP sees as 1 big monitor with a resolution of 3840x1024
So as far as GridMove is concerned, It's just one monitor.
Now I want to divide it into 3 equal parts, al of which are 1280 pixels wide (3 monitors of 1280x1024 makes a total of 3840x1024, so area 1 coincides with the screenarea of monitor 1, area 2 is monitor 2,  and 3 is, you guessed it!;D ; monitor 3)

Now then, what do I use as "commands" in the grid file, cause it seems there are only commands like left/ right and not "center"

Any help is greatly appreciated! (not to mention a custom grid made for this purpose... :D)

Thanks in advance!
Martin

Add:
by studying the other grids I cam up with a solution! (by multiplying the screenwidth with thirds)
So for the interested here is the syntax:
(just put in a notepad file and save it as: "whatever name you want to give it".grid  (yes change the extension from .txt to .grid   and put it in the folder called Grids where you saved the Gridmove program)


[Groups]

NumberOfGroups = 3

[1]

  TriggerTop   = [Monitor1Top]
  TriggerLeft  = [Monitor1Left]
  TriggerBottom= [Monitor1Bottom]
  TriggerRight = [Monitor1Left] + [Monitor1Width] /3
 
  GridTop   = [Monitor1Top]
  GridLeft  = [Monitor1Left]
  GridBottom= [Monitor1Bottom]
  GridRight = [Monitor1Left] + [Monitor1Width] /3
 
[2]

  TriggerTop   = [Monitor1Top]
  TriggerLeft  = [Monitor1Left] + [Monitor1Width] * 0.33333
  TriggerBottom= [Monitor1Bottom]
  TriggerRight = [Monitor1Left] + [Monitor1Width] * 0.66666
 
  GridTop   = [Monitor1Top]
  GridLeft  = [Monitor1Left] + [Monitor1Width] * 0.33333
  GridBottom= [Monitor1Bottom]
  GridRight = [Monitor1Left] + [Monitor1Width] * 0.66666 +2
 
[3]

  TriggerTop   = [Monitor1Top]
  TriggerLeft  = [Monitor1Left] + [Monitor1Width] * 0.66666
  TriggerBottom= [Monitor1Bottom]
  TriggerRight = [Monitor1Left] + [Monitor1Width]
 
  GridTop   = [Monitor1Top]
  GridLeft  = [Monitor1Left] + [Monitor1Width] * 0.66666
  GridBottom= [Monitor1Bottom]
  GridRight = [Monitor1Left] + [Monitor1Width] +1
 

Pages: [1]